IKCO Die Design Standards 1 , 2

IKCO Die Design Standards 1 , 2
اسم المؤلف
DIE & PRESS ENG. MANAGEMENT
التاريخ
25 مارس 2019
المشاهدات
التقييم
Loading...

IKCO Die Design Standards 1 , 2
ENGINEERING CENTER
DIE & PRESS ENG. MANAGEMENT
I.K.CO 01 o GENERAL ITEMS I.K.S – SD 0..
PAGE: 2 OF: 3
DIE DESIGN STANDARD INDEX DATE: 10/2001
Standard
No. Items Page
No.( SD )
1 CASTING CONSTRUCTION SD030 23
General items for casting 1-7
Rib & core shape 8-12
Protruded surface 13-14
Core holes 15-20
Chamfering 21
Dimensional tolerance for PMC 22-23
2 GUIDE SD032 15
Guide post 1-2
Heel guide 3-4
Clearance of sliding part 5
Heel engagement 6
Guide bar 7-8
Heel & guide post 9-13
Standard for fool proof 14-15
3 LIFTING SD034 14
Lifting methods 1-7
Relationship for gravity center & lifting center 8
Notification on using wire ropes 9-13
Transport 14
4 MACHINING SD036 3
Machining on bottom place surface 1
Surface and hole machining on side 2
Installing on sliding surface of profile area 3
5 FINISH SURFACE SD038 1
6 CENTER DIE SD040 2
Master hole 1
Datum face & key slot 2
7 CLAMPING SLOTS SD042 4
Number and dimension 1-2
Auto clamping 3-4
8 SEFETY AREA SD044 1
Number & dimension 1GENERAL ITEMS I.K.S – SD 0
PAGE: 3 OF: 3
I.K.CO
DIE DESIGN STANDARD
ODBO
INDEX DATE: 10/2001
Standard
No. Items No.( SD ) Page
9 STROKE END BLOCK SD046 2
Stop block 1
Stocking 2
10 PAD SD048 8
Structure 1-2
Bottoming clock 3
Guide 4-5
Pad guide & dimension for small dies 6
Pad relief 7
# Retainer pad ( Bolt ) 8
11 CUSHION PIN SD050 5
Extension 1-5
12 LOCATING SD052 9
Method for locating 1-9
13 SAFETY COVER SD054 1
14 SECTIONAL & INSERT STEELS SD056 11
Standard shape 1-2
Separation 3-4
Separation of cutting steel 5
Installing cast steel 6
Installing steel 7
Steel installed on sectional type 8
Checking edges squareness 9
Fastening 10-11
15 STEELS TABLE SD058 1
16 HEAT TREATMENT SD060 3
Local hardening specifications 1-2
Surface treatments hard chrome 3
17 DIE PAINTING SD062 6
Die painting standard 1-6
18 LOAD & UNLOAD SD064 3
Manual loading & unloading 1
Auto loading & unloading 2-3
18 BOTTOMING MARKER SD066 2
Dimension & notes 1-2
I.K.CO
DIE DESIGN STANDARD
I.K.S – SD 2..
PACE:2 OF: 3
I TRIM & PIERCE DIE
£ INDEX DATE- 10/2001
Si Standard
No.( SD )
I£ No. Items Page
1 CONSTRUCTION SD300 2
Ribs dimension 1
Material 2
1 2 CALCULATION SD302 2
Trim & pad pressure 1-2
3 CLEARANCE SD304 1
Clearance between punch & die 1
4 WELDING SD306 1
Welded edge 1
7 5 INSERT STEEL & SECTIONAL SD308
i Standard shape
Separation of cutting steel
6 TRIM CONDITION SD310 3
Pinch trim & trim on the angle surface 1
Trim across the angled surface 2-3
7 SCRAP CUTTER SD312 5
Standard shape 1
Entrance 1
Layout 3
8 SCRAP DISPOSAL SD314 1
Latch arm
9 SCRAP CHUTE SD316 7
Scrap shedding in to the pit 1
Scrap chute at the side 2-3
Scrap chute at front & back 4
Channel for scrap chute 5
Scrap more than two area 6
Size of scrap chute 7
10 SHEAR ANGLE SD318 1
11 PIERCE PUNCH SD320 16
Kind of pierce punch & retainer 1-2
pierce punch & retainer selection 3-8
g pierce punch acceptable angle 9
Piercing on two slope surface 10
I pierce punch entry 11r
I.K.S- SD 2
RAGE- 3 OF: 3
TRIM & PIERCE DIE
DIE DESIGN STANDARD INDEX DATE 10/2001
Standard
i& No. Items No.( SD ) Page
$. Stripper 12
? Home made pierce punch 13
Notching punch 14
ef. Pierce & flange 15
Counter pierce hole 16
12 Die SD322 1
Insert die 1
* 13 BOTTOM Die SD324 6
General note for use 1-2
*1 Bottom die adjacent 3
Bottom die angle 4
Bottom die holder 5
Slug chute 6
14 PAD SD326 3
Pad stroke 1
Pad strength 2
Relief & clearance 3
كلمة سر فك الضغط : books-world.net

The Unzip Password : books-world.net

تحميل

يجب عليك التسجيل في الموقع لكي تتمكن من التحميل
تسجيل | تسجيل الدخول

التعليقات

اترك تعليقاً